• Login
    Buscar 
    •   AEIPRO Principal
    • Buscar
    •   AEIPRO Principal
    • Buscar
    JavaScript is disabled for your browser. Some features of this site may not work without it.

    Buscar

    Mostrar filtros avanzadosOcultar filttos avanzados

    Filtros

    Use filtros para refinar sus resultados.

    Mostrando ítems 1-9 de 9

    • Opciones de clasificación:
    • Relevancia
    • Título Asc
    • Título Desc
    • Fecha Asc
    • Fecha Desc
    • Resultados por página:
    • 5
    • 10
    • 20
    • 40
    • 60
    • 80
    • 100
    Thumbnail

    APLICACIÓN DE UNA NOVEDOSA METODOLOGÍA EN EL DISEÑO DE UN SEMIRREMOLQUE DE CUELLO REDUCIDO 

    Malón Litago, Hugo (2014)
    Until recently, the design of new models of semitrailer has been performed based on the experience of the manufacturers of such vehicles. In the last five years the Department of Mechanical Engineering of the University ...
    Thumbnail

    ENSAYO Y OPTIMIZACIÓN MEDIANTE EL MÉTODO DE LOS ELEMENTOS FINITOS DE UN BASTIDOR AUXILIAR DE CAMIÓN CON GRÚA AUTOPORTANTE 

    Malón Litago, Hugo; Valladares Hernando, David; Carrera Alegre, Marco; Castejón Herrer, Luis; Martin-Buro Martín, Pedro; Lozano Martín-Buro, Ramón (2014)
    Today the crane assembly on trucks is done by installing steel sub-frames. These sub-frames reinforce and stiffen the original chassis of the trucks. The correct design of these components allows the proper functioning of ...
    Thumbnail

    ANÁLISIS DEL DISEÑO Y OPTIMIZACIÓN DE UN CONTENEDOR CISTERNA FRENTE AL FENÓMENO DE "OLEAJE" 

    Malón Litago, Hugo; Labarta, Vicente; Cuartero, Jesús (2017)
    Tank containers are intermodal containers for transport liquids, gases and powders in bulk in trucks, trains or ships. In recent years its use has been increased mainly for three reasons which are to give a greater security ...
    Thumbnail

    CARACTERIZACIÓN DEL FLUJO DE AIRE GENERADO POR PULVERIZADORES HIDRONEUMÁTICOS MEDIANTE DINÁMICA DE FLUIDOS COMPUTACIONAL (CFD) 

    Boné Garasa, Antonio; Vidal Cortes, Mariano; Malón Litago, Hugo; Puyuelo Baseca, Javier; García Ramos, Francisco Javier (2014)
    The air-assisted sprayers are commonly used to apply chemical products in orchards. The sprayer generates small droplets (around 200 m diameter) which are transported to the crop in an air flow generated by a fan powered ...
    Thumbnail

    DISEÑO Y OPTIMIZACIÓN DEL CHASIS DE UN PULVERIZADOR HIDRONEUMÁTICO DE DOS VENTILADORES MEDIANTE EL MEF 

    Malón Litago, Hugo; García Ramos, Francisco Javier; Vidal Cortes, Mariano; Boné Garasa, Antonio (2014)
    The application of phytosanitary products in plantations of fruit trees are made by trailed agricultural sprayers. Current demand is requesting larger implements that improve the results of the treatments. In order to ...
    Thumbnail

    DESARROLLO DE UN BANCO DE ENSAYOS PARA EL ANÁLISIS EXPERIMENTAL DE ESTRUCTURAS COMPLETAS DE SEMIRREMOLQUES 

    Carrera Alegre, Marco; Malón Litago, Hugo; Valladares Herrando, David; Castejón Herrer , Luis; Martín Lafuente, Carlos (2015)
    This paper shows the process of design, development and implementation of the first test bench developed for the heavy vehicles industry, able to analyze the structural behavior of a full semi-trailer under fatigue loading. ...
    Thumbnail

    EVALUACIÓN DE SISTEMA DE PROTECCIÓN TRASERA ANTIEMPOTRAMIENTO EN SEMIRREMOLQUE ANTE IMPACTOS CON SOLAPAMIENTO PARCIAL DE AUTOMÓVIL UTILIZANDO EL M.E.F. 

    Valladares Hernando, David; Carrera Alegre, Marco; Malón Litago, Hugo; Castejón Herrer, Luis (2015)
    The current European regulation concerning rear underrun protection systems in semi-trailers collected in Directives 79/490/CEE and 2006/20/CEE, requires the fulfilment of several tests consisting in the application of an ...
    Thumbnail

    DISEÑO, CÁLCULO Y ENSAYO DE UN SUELO OPTIMIZADO DE 5 METROS PARA LA ZONA DE CARGA DE UN CAMIÓN 

    Cuartero Salafranca, Jesús; Castejón Herrer, Luis; Malón Litago, Hugo; Perez, Victor (2015)
    In recent years, fuel consumption and competition in transport have generated that the vehicles optimization is a critical phase in the design of all types of vehicles. The developed study include the design, numerical ...
    Thumbnail

    Diseño de una matriz con mayor número de cavidades para la fabricación de piezas industriales mediante sinterizado 

    Malón Litago, Hugo; Llena Chesa, Isabel; Valladares Hernando, David; Castejón Herrer, Luis (2019)
    Sintering is a precision manufacturing process for producing industrial components in large series, without material loss, highly reliable and economical. In one phase of this manufacturing process, metallic powder is ...

    DSpace software copyright © 2002-2016  AEIPRO
    Contacto | Sugerencias
     

     

    Listar

    Todo AEIPROComunidades & ColeccionesPor fecha de publicaciónAutoresTítulosMaterias

    Mi cuenta

    Acceder

    Descubre

    Autor
    Malón Litago, Hugo (9)
    Castejón Herrer, Luis (4)Carrera Alegre, Marco (3)Valladares Hernando, David (3)Boné Garasa, Antonio (2)García Ramos, Francisco Javier (2)Vidal Cortes, Mariano (2)Castejón Herrer , Luis (1)Cuartero Salafranca, Jesús (1)Cuartero, Jesús (1)... másMateria
    Ingeniería de Producto, Procesos y Diseño Industrial (9)
    ... másFecha2014 (4)2015 (3)2017 (1)2019 (1)Has File(s)Yes (9)

    DSpace software copyright © 2002-2016  AEIPRO
    Contacto | Sugerencias